USA Ship!Wantai 3Axis Stepper Motor Nema23 57BYGH627 270oz-in 3A 4-Lead &Driver

Description

Welcome to my Store!
Ship from
USA
warehouse ,
after payment, within 3 days for receiving products!
No taxes from customs, no damage, better service, please don't hesitate! Free Ship by
UPS
!
This item includes:
3PCS Stepper Motor Nema23 57BYGH627
SINGLE SHAFT
3A 270oz-in 4 wires
3PCS Stepper Motor Driver DQ542MA 4.2A 50V 128Microsteps
1PC Power Supply 350W 36V
1PC Breakout Board&1PC Cable For
free
Pls confirm the shipping method and shipping fees before pay!
Feel free to contact me for any question!
1 Stepper Motor:57BYGH627 single shaft
Part No.:
57BYGH627
single shaft
Frame Size:                    NEMA23
Step Angle:                    1.8 degree
Voltage:                          3.0VDC
Current:                          3.0
A
/phase
Resistance:                    1.0 Ohm/phase
Inductance:                    3.5 mH/phase
Holding torque:             19
Kg
-cm
270
oz
-in
Rotor inertia:                  480
g
-cm2
Detent torque:
0.6 kg
-cm
Number of wire leads:    4
Weight:
2.20lb
(
1.0 kg
)
Length:
76mm
Shaft diamter:                  6.35mm (1/4")
Black      A+
Green     A-
Red         B+
Blue        B-
2 Stepper Motor Driver:DQ542MA
Introduction:
DQ542MA is a type
of two-phase hybrid stepping motor driver, the drive voltage of it is from 18VDC to 50VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 42mm to 86mm outside diameter and less than 4.0A phase current. This circuit that it adopts is smiliar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Holding torque when DQ542MA run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, and computer embroider machine, packing machines and so on
.
Features:
l
High performance, low price
l
Average current control, 2-phase sinusoidal output current drive
l
Supply voltage from 18VDC to 50VDC
l
Opto-isolated signal I/O
l
Overvoltage, under voltage, overcurrent, phase short circuit protectio
l
15 channels subdivision and automatic idle-current reductio
n
l
8 channels output phase current setting
l
Offline command input termina
l
l
Motor torque is related to speed, but not related to step/revolution
l
High start speed
l
High hording torque under high spe
ed
Electrical specification:
Input voltage
18-50VDC
Input current
＜
4A
Output current
1.0A
～
4.2A
Consumption
Consumption
：
80W
；
Internal Insurance
：
6A
Temperature
Working Temperature
-10
～
45
℃
；
Stocking temperature
-40
℃
～
70
℃
Humidity
No condensation, no water droplets
gas
Prohibition of combustible gases and conductive dust
weight
300G
3.  Power Supply:350W 36V
350W Single Output Switching Power Supply
AC input range selected by switch.
Protections:short circuit/overload/over voltage/over temperature
100% full load burn-in test
Low cost,high reliability
1 year warranty
Size: 215*115*50mm
Weight:1.05kg
AC input voltage range: 90
～
132VAC/180
～
264VAC
AC inrush current: cold start 25A/115V,50A/230V
DC adjustment range:±10% rated output voltage
Overload protection:105%
～
135%, hiccup mode, auto recovery
Setup,rise,hold up time: 200ms,50ms,20ms/230VAC at full load
Working temperature and humidity:-10℃
～
+60℃
；
20%
～
90 %RH
Model
DC output voltage,
Current range
Voltage tolerance
Ripple
&Noise
Efficiency
S-350-
36
36
V,0
～
9.7
A
±1%
150mV
83%
4 Breakout Board:
Set pins according to software as follows:
Output pin: P1,P2,P3,P4,P5,P6,P7,P8,P9,P14,P16,P17
.
l
P2
–
X axis Pulse, P3 – X axis Direction
l
P4
–
Y axis Pulse, P5 - Y axis Direction
l
P6
–
Z axis Pulse, P7 – Z axis Direction
l
P8
-
A axis Pulse, P9 - A axis Direction
l
P14
-
B axis Pulse, P1- B axis Direction
l
P16
-
C axis Pulse, P17- C axis Direction
Input pin
:
P10 ,P11, P12, P13
,
P1
5
l
Set
them for Emergency Stop and X Y
Z Limit switch
Shipping:
Ship from
USA
warehouse by
UPS to
USA
, no tax faster delivery,better price
!
Problem and feedback:
Please give us the opportunity to resolve any problem when you have, we will try our best to help
you
.
Your satisfaction is is of the utmost importance for us, so please contact us before you
want
to
leave a negative feedback.
Refund:
If you are not satisfied with the package, please tell us the reason.
Delivery cost must be paid by the buyer.
Honor:
Changzhou Wantai Electrical Appliance Co.,Ltd has powerful technology, mature
technics
and
complete testing equipment.
And we have obtained ISO9001:2000 certification, CE
certification and all of our
products
conform to RoHS requirements.
Note:
we can manufacture products according to our customer's requirements.
Appliaction:
Our product are mainly used in Aerospace & Defense, Automation
Applications,
Commercial
Equipment, Industrial Tool,
Medical Device & Equipment, Medical Mobility, Printing &
Imaging, Pump,
Semiconductor
Equipment, Vehicle, , Milling
Machine, Engraver Machine, CNC
Routers Applications,etc.
Contact US:
Changzhou
Wantai Electrical Appliance Co.Ltd
Tel:0086-519-85138377
Fax:0086-519-85139178
Contact: Ada
Skype:
wantai.motor.ada
Mobile:0086-15151992336