THB6128 Stepper Motor Driver/MOSFET driver/DIP Switch/2A Current /Max 36V

Description

Visit store
Items for sale
About us
Product Details
Description:
This module is based on the original imported Toshiba stepper motor drive chip THB6128 design, can drive 57 and the following two-phase four-wire stepper motor.
The module has the following advantages：
chip using double full-bridge MOSFET driver, low on-resistance Ron = 0.55Ω
maximum voltage 36V, peak current 2.2A, continuous current 2A, the current set by DIP switch simple set
1, 2, 4, 8, 16,32,64,128 a variety of sub-optional, subdivided through the DIP switch to set
chip with automatic half-flow lock function, greatly reduce the heat when the motor is locked
chip built-in temperature protection, over-current protection
built-in 5V logic signal supply regulator chip, and add a current limiting resistor to reduce the chip fever when the input high voltage
Input voltage side reverse polarity protection
Reasonable alignment, clear identification, reliable and stable
module diagram is as follows:
Signal interface
The module has three sets of input signals, namely CP pulse signal, DIR direction signal, EN enable signal.
The electrical diagram of the signal is as follows:
When the external signal amplitude is 3.3-5V, the current limiting resistor R can not be connected, when the signal amplitude exceeds 5V, the input signal must be limited to ensure that the optocoupler input current of 8mA-15mA, the specific calculation method For: optocoupler conduction voltage drop is generally 1.1-1.3V or so, take 1.2V, then
Optocoupler current = (voltage amplitude - optocoupler conduction voltage drop 1.2V) / (R + 330)
Special Note:
If the optocoupler operating current exceeds 20mA, the optocoupler life will be greatly reduced.
The input signal interface is characterized by: the user can be used as needed common anode connection or common cathode connection.
1, common anode connection: respectively CP +, DIR +, EN + connected to the control system power supply. The signal is input from the CP-, DIR-, EN- side and works at low level.
2, the common cathode connection: CP-, DIR-, EN-, respectively, connected to the control system to the ground (SGND, isolated from the power supply), the signal from the CP +, DIR +, EN + side input, and play a role in the high level.
Subdivision settings
The subdivision is set by the DIP switch S2, the specific correspondence table is as follows:
subdivision
1
2
3
1
ON
ON
ON
2
OFF
ON
ON
4
ON
OFF
ON
8
OFF
OFF
ON
16
ON
ON
OFF
32
OFF
ON
OFF
64
ON
OFF
OFF
128
OFF
OFF
OFF
Hybrid two-phase stepper motor step foot is generally 1.8 °, that is, single-step 360 / 1.8 = 200 steps, the number of single-turn pulse is 200 * n, n for the breakdown.
For example, using 16 subdivision, the number of single-turn pulses should be 200 * 16 = 3200, that is, from the CP input 3200 pulses, stepping motor turn a full circle.
Current setting
This module uses the resistor divider way, to the chip VREF feet to provide the reference voltage, and through the DIP switch S1 to select the resistance. Defined as follows:
Current
1
2
3
4
2A
OFF
OFF
OFF
OFF
1.7A
OFF
OFF
OFF
ON
1.5A
OFF
OFF
ON
OFF
1.3A
OFF
OFF
ON
ON
1A
OFF
ON
ON
ON
0.7A
ON
ON
ON
ON
Current
The table lists the common current corresponding to the block code switch combination, the rest of the combination of ways to achieve other phase current settings. This can be calculated by measuring the voltage at the test point Vref. The formula is:
When the motor is running,
Motor phase current = Vref * 2
When the motor is locked, due to half-flow lock reasons, Vref is also automatically halved,
Motor phase current = Vref * 4
Current attenuation mode
The module uses two 4.7K resistors, the VFDT pin voltage is set to 2.5V, that is, mixed attenuation mode, is the most commonly used mode. In this mode, the motor high-speed or low-speed operation will be normal. If you need other attenuation mode, please adjust the voltage divider. The FDT voltage and attenuation modes given in the chip manual are as follows:
Package Included:
1 X THB6128 Stepper Motor Driver Module
Payment Method
Shipping Policy
Returns & Refund Policy
Feedback
Payment Method
EBAY Managed Payment.
But we only
Accept
your
Ebay Address
, please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping Policy
1. We only ship to the confirmed address provided by eBay. please make sure your ebay address is 100% matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand.
2. Orders will be processed instantly and dispatched within 1-3 business days except hoilday, so we do NOT accept any email/message note after you place orders.
3. All package need to wait 30 days,Please take care it.Less than 30 days,we can't take a refund.
Returns & Refund Policy
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please keep in touch with us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
Feedback
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you keep in touch with us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.