7A 160W Dual DC Motor Drive Module L298 Logic Positive Negative PWM Speed XY160D

Description

Product Overview
7A 160W Dual DC Motor Drive Module L298 Logic Positive Negative PWM Speed XY160D
Product Highlights:
1. Double H bridge, which can drive two DC motors with single 7A current, high power;
2. Wide voltage input 6.5V ~ 27V;
3. Signal optocoupler isolation input, IO port can be directly controlled, without interference;
4. Undervoltage protection, to prevent instantaneous high-current burned module;
5. High-power TVS and electrostatic discharge circuit, inhibit the transient interference pulse and static, enhanced EMC performance, stable and reliable product, industrial design.
Control signal logic
Note
: Where 0 is low, 1 is high level, × is any level, when floating high.
1. 1 # motor interface control signal logic
IN1
IN2
ENA1
OUT1
.
OUT2
0
0
×
brake
1
1
×
Floating
1
0
PWM
Forward to speed
0
1
PWM
Reverse speed
1
0
1
Full speed forward
0
1
1
Full speed reversal
2. 2 # motor interface control signal logic
IN3
IN4
ENA2
OUT3
.
OUT4
0
0
×
brake
1
1
×
Floating
1
0
PWM
Forward to speed
0
1
PWM
Reverse speed
1
0
1
Full speed forward
0
1
1
Full speed reversal
Product parameters:
1. Power supply voltage 6.5V-27V, power supply must not be connected to or over 27V, otherwise it may                burn out the module, it is recommended that the power input in series 15A fuse.
2. Dual motor interface, each rated output current 7A, peak current 50A, the motor interface must not                        short-circuit, the proposed series 10A fuse.
3. Control signal voltage 3-6.5V, respectively, is the enable signal and the positive inversion control signal.
4. Enable signal terminal (ENA) input PWM adjustable speed, PWM frequency range 0-10KHZ, PWM                     minimum pulse width 10us.
5. Working temperature -25 ℃ -80 ℃.
6. Product size: 55 x 55 x 16mm (length and width).
7. Installation hole diameter: 3mm, attention should be paid to prevent short circuit on the back of the                       circuit, you can add insulation pad or copper column to raise the circuit board.
Suitable for motor parameters:
Rated voltage 24V of the motor, the appropriate identification of rated power 115W and below or rated current of 7A or less the following long-term work of the motor.
Rated voltage 12V of the motor, the appropriate identification of rated power 40W and below or rated current 7A rated below the motor for a long time full of work.
Precautions
:
1. Drive power must not be reversed, the proposed power connector in series 15A fuse, the voltage should be between 6.5 ~ 27V. If the voltage is over-voltage, power-on may burn the drive module.
2. It is recommended that the rated output current of the power supply should be at least 2 times of the rated current of the motor so that the power supply can not supply the required voltage when the motor starts.  Off the output lead to the phenomenon of motor pause.
3. Do not short-circuit the motor interface, or may burn the driver module, the proposed electrical interface in series 10A fuse.
4. In the forward and reverse switch when the need to brake 0.1S above and then reverse, not in the motor has not stopped when the commutation, or it may damage the drive.
5. Drive module power-down, do not directly or indirectly, high-speed rotation of the motor, or motor                   generated electromotive force may burn the drive module.
If the application requires a high-speed rotation of the motor when the drive module is powered down, it is     recommended that the motor interface of the driver is connected in series with a relay (NO and COM             terminals), and the relay coil and the driver are connected in common. In this way, when the power down, the relay will disconnect the drive and the motor connection.
6. CAUTION Do not expose the drive to moisture. Do not short-circuit the components on the drive board.
Do not touch the pins and pads on the board.
7. Before you use the baby carefully read the description, as a result of damage caused by improper use of the module, do not change.
Package Include:
1 x  7A 160W Dual DC Motor Drive Module Positive Negative PWM Speed L298 Logic XY160D
Shipping Policy
Item Location
Payment Mathord
Returns Policy
About Feedback
Shipping Policy
1. We Ship to Worldwide
2. We ship your orders within 1-2 business days after the payment cleared.
3. Item shipped from China via china Post Airmail, reach most of the countries within 2 to 4 weeks.
4. Delivery time depends on destination and other factors, it may takes up to 20 days. If you don't receive
the item after 25 days,please keep in touch with us, we'll investigate and solve the delivery problem.
5. Import duties, taxes, and charges are not included in the item price or shipping cost. These charges
are the buyer's responsibility. Please check with your country's customs office to determine what these
additional costs will be prior to bidding or buying.
Item Location
ShenZhen
Payment Mathord
1. We accept PAYPAL only.
2. Payment must be made within 7 days of auction closing (Unpaid dispute will automatically open when item
is not paid in 7 days).
3. PLEASE NOTE: SHIPPING&HANDING DOES NOT INCLUDE DUTIES, LOCATL TAXES OR ANY OTHER IMPORTATION FEES.
4. Please list your special requests (color, packages, value of declaration, etc.) in the EBAY NOTES SECTION
when you make payment
Returns Policy
1. Customer satisfaction is our top goal. All products are quality checked. They are new and in good
condition when shipped to our customers. If product is defective or damage upon arrival, or wrong
product shipped, please keep in touch with us immediately. Returns accepted within 14 days of delivery date
and item must be in original new condition, not worn or altered in any way with attached tags & wrap.
Otherwise deal is final. Return shipping must be paid by buyer.
2. Please keep in touch with us first if you have anyproblems/questions/concerns. We will be happy to resolve
any issues you may have in a cordial and friendly manner.
3. We appreciate your Positive Feedback, and will do the same in return. PLEASE DO NOT leave
negative feedback without first communication with us. Please allow max 24 HOURS for us to respond
About Feedback
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is
very important to us. We request that you keep in touch with us immediately BEFORE you give us neutral or
negative feedback, so that we can satisfactorily address your concerns.It is impossible to address
issues if we do not know about them!